Question 1

Will the Stepcraft Laser DL445 attachment give off fumes when in use?

stepcraft · Accepted Answer

Yes, since it is essentially burning through the workpiece, some fumes will be produced. However, the system includes a built in exhaust extraction system with a fine particle filter to reduce the breathable fumes. It is recommended that you connect the output of the exhaust system to the outside of your work environment using flexible hose or PVC pipe (sold separately). This will ensure that the fumes are exhausted outside and not within the room your are working in.

Question 2

Will the milling and laser tools work on other metals besides aluminum?

stepcraft · Accepted Answer

Will the milling and laser tools work on other metals besides aluminum?

Yes, they will also machine brass and copper. STEPCRAFT machines are only designed for machining of non-ferrous metals. So you can not mill steel, stainless steel, etc. Also note that the laser will NOT cut metals. you can use it to engrave but it will NOT cut!

Question 3

Why is my laser positioning light is not visible?

Hugo Neil · Accepted Answer

Why my laser positioning light is not visible?

Turn the power key switch to the ON position.

Move the laser head approx. 20mm above work piece to focus positioning laser beam clearly.

To enable the positioning light, move the zero point sensor to the middle position and the light should turn on.

The positioning light is a class 2 laser with far less power (comparable to a laser pointer).

If your laser positioning guide wont turn on after following this procedure please contact our support team and they can guide you on how to fix this issue.

Question 4

What Vectric Post Processor do I use for the Stepcraft DL-445 Laser?

stepcraft · Accepted Answer

We have a special post processor that you need to use for the laser. You can download that file [here] You need to place the file in the correct folder in your Vectric Program. Do do this, open your program (V Carve, Cut 2D, etc) In the FILE Menu, select OPEN APPLICATION DATA FOLDER

Look for a "PostP" or "My_PostP" folder

Copy the laser post processor file (downloaded above) Into both of these folders. NOTE: if you copy the file into the My_PostP folder then when you open your Vectric Program, only the post processors in this folder will show. So I always recommend copying the post processors for my CNC into this folder so when you go to create a G Code file, you will not have to scan though a ton of files for other machines. If you do not want to use the My_PostP folder then simply copy the above Laser profile into the PostP folder and you will see it in the list of post processors. ALSO, you will need to restart the program for the post processor to be visible in the list

Question 5

What software do I need if I want to use the Laser Attachment with my STEPCRAFT?

stepcraft · Accepted Answer

The STEPCRAFT CNC comes with UCCNC machine control software, which also has a plug in that will transform a bitmap image into G Code for use with the Laser so you can laser engrave a photo or other bitmap image. However, if you wish to use the laser to cut projects out, then you need a CAM program like Vectric Cut 2D or V Carve to make the tool path for the laser to follow and then output the G Code for UCCNC to read.

To summarize:

For photos/bitmap engraving - No, you don't need additional software

For cutting - Yes, you need a CAM program like Vectric Cut 2D/V Carve

Question 6

What is the wattage of your Laser and how does it compare to a typical laser cutter?

stepcraft · Accepted Answer

The laser is 2 watts. This is a different type of laser than the more common CO2 laser machines.  CO2 Lasers tend to be more powerful, but also larger and consume more power.  CO2 lasers need to be fully enclosed because the laser is generated from a large glass laser tube that is fixed on the back of the machine.  The beam is then directed via mirrors to the laser head where it is focused and sent to cut/engrave the material.  The laser tubes on these machines get very hot and require external water cooling.

The STEPCRAFT laser is a solid state design which uses a laser diode (blue beam) that runs through a focusing lens and sent to the work material.  While a 2 Watt laser does not sound as impressive as a 50 or 100 watt CO2, it is still surprisingly functional with the capability to cut through thinner materials (1/8" or less wood and plastic) as well as a wide variety of engraving tasks.  The STEPCRAFT CNC machine can not use a CO2 laser design because it is an open gantry machine and bouncing a laser beam around would be very dangerous. The Laser attachment will give you a lot of flexibility at a small fraction of the cost.  The laser diode is contained right in the laser head and there are a lot of safety measures that have been designed into the product to ensure that you can have maximum flexibility on a CNC router.

Question 7

Does the Laser DL445 use the same port on the STEPCRAFT as the 3D Printer and HF500 spindle?

Erick Royer · Accepted Answer

Does the Laser DL445 use the same port on the STEPCRAFT as the 3D Printer and HF500 spindle?

Yes, they both use the same serial port on the back of the machine. You would need to disconnect the cable and reconnect the attachment that you wish to use. STEPCRAFT also offers a Switchbox which allows you to connect everything and simply turn the dial to select the attachment you wish to use. This is very handy if you are constantly changing attachments.

Question 8

Can I engrave a photograph into a piece of wood?

stepcraft · Accepted Answer

Can I engrave a photograph into a piece of wood?

Yes, you can use Vectric's PhotoVCarve program, which allows you to create an engraving tool path for photos. Additionally, you can use the new Laser Engraving Head DL445 which can laser engrave your photos into a variety of materials.

Question 9

Are all of the machines capable of using the spindle, laser and 4th axis?

stepcraft · Accepted Answer

Are all of the machines capable of using the spindle, laser and 4th axis?

Yes, you can use all of these attachments on each of the machines. However the small size of the STEPCRAFT-1/210 might make it tough to use the 4th axis with longer work pieces. Additionally, the 210 has a limited 3" Z height, which does not leave a lot of vertical travel and will limit the diameter of material that you can use on the machine. Additionally you really need a T-slot when using the 4th Axis so you can adjust the tail stock for the length of the work material and the 210 is the only machine that does not have a T-Slot option.

Question 10

Why is my laser positioning light is not visible?

Hugo Neil · Accepted Answer

Why my laser positioning light is not visible?

Turn the power key switch to the ON position.

Move the laser head approx. 20mm above work piece to focus positioning laser beam clearly.

To enable the positioning light, move the zero point sensor to the middle position and the light should turn on.

The positioning light is a class 2 laser with far less power (comparable to a laser pointer).

If your laser positioning guide wont turn on after following this procedure please contact our support team and they can guide you on how to fix this issue.

3D Printing

3D Print Questions

Does the Laser DL445 use the same port on the STEPCRAFT as the 3D Printer and HF500 spindle?

Does the Laser DL445 use the same port on the STEPCRAFT as the 3D Printer and HF500 spindle?

Why is my laser positioning light is not visible?

Why my laser positioning light is not visible?