STEPCRAFT Assembly Questions


Working With Metals

Will the milling and laser tools work on other metals besides aluminum?

Yes, they will also machine brass and copper.  STEPCRAFT machines are only designed for machining of non-ferrous metals.  So you can not mill steel, stainless steel, etc.

Also note that the laser will NOT cut metals.  you can use it to engrave but it will NOT cut!

 

How come my circles are not perfectly round?

Then you are machining circles on a CNC and your circles are not coming out perfectly round, it is commonly caused because there is some backlash developing on the machine.  Backlash is a tiny amount of play that appears over time and is noticed when a drive changes direction.

When running in a positive direction, the gears/lead screw are engaged with the lead screw nut on the gantry, but when the stepper motor reverses direction there is a tiny space between the lead screw and the lead screw nut that has to be made up before there is positive engagement in that direction.  After many, many hours of use or if your machine is not properly maintained and lubricated, then this backlash can develop.

If this is happening to you, please download this document: Stepcraft UCCNC Backlash Compensation.

This will show you how to setup backlash compensation in UCCNC so that you can “dial” out any backlash and go back to having perfect circles again.

 

 

This really depends on the bit you are using and what the flute length is.  If you are using a bit with a 0.5″ flute length then your maximum thickness would be 0.5″.  Keep in mind that when you go thicker than 0.125″ thick aluminum, you have to be very careful to take care of chip evacuation. When your end mill starts to make a deep channel that is the width of the bit, then chips will fall in the channel and when the bit rotates, it can recut the chips causing excessive heat, chatter, welding of the chips to the tip of the bit or breaking the bit.  A way around this for deeper cuts is to create a pocket around the perimeter that is wider than the bit so if chips fall in the channel they are not “forced” into the wall by the cutter.  You should also use compressed air to continually blow the chips away from the bit and the channel.

We have successfully cut through 1″ thick aluminum blocks without a problem. Keep in mind that this is a CNC router and not a CNC mill, so it is not designed to be as aggressive with your feeds, speeds and pass depths.  Take care to not push the machine, spindle or end mill past its limits.

 

 

No, you do not need to use different spindles.  The main factor will be how fast the feed rate will be that you run and how much material you remove per pass.

If you with to run a light duty spindle like a Dremel 4000, you can run wood, plastics and metals just as well as if you were using a Kress 800W spindle. The only difference is that you will not be able to remove as much material and your feed rate will be slower the harder the material is.

Keep in mind that dedicated CNC spindles will have better quality bearings which will offer less runout and therefore a longer life span and higher accuracy.  Using the Dremel example, this device is not meant for hours and hours of prolonged use, nor is it made to have lots of pressure side loading the main shaft.  You will find that if you are not careful on the feed rate and pass depth that you will quickly wear out the bearings.

A router like the Dewalt DW611 will also cut all types of material, but as with the Dremel, the bearings are not as good as with a dedicated spindle so you can expect more runout with a router.  The STEPCRAFT HF500 is a purpose built spindle that was designed to work with all types of materials and has an excellent bearing system that provides very little runout and a much higher accuracy.

The bottom line is that you can pretty much cut whatever you like with just about any spindle.  You just need to be cautious on feed rates and pass depth.

No, the STEPCRAFT is only designed to cut non-ferrous metals like brass, aluminum and copper.  You might be able to engrave steel with the right engraving bit and proper speed and feed settings, but you can not cut it.

Can I use MDF as a spoil board when cutting aluminum?

Often times when cutting aluminum you will need a spoil board under the aluminum, especially when you are cutting all the way through the material.  MDF is a very common material to use as a spoil board for the following reasons:

  • There is no grain so it cuts the same in any direction
  • It is usually pretty flat
  • It cuts easily so when your bit goes through your work piece, there is no additional strain on it when it makes contact with the MDF
  • It is easy to find and relatively inexpensive.

Some things to be careful of when machining aluminum with an MDF spoil board:

  • Make sure the MDF is secured well to the machine bed
  • Make sure the Aluminum is clamped tight to the MDF/machine bed – if it is not you will get vibration, chatter, poor cut finish, and can possibly break your cutting bit.
  • You can not use any lubricant when you use an MDF spoil board!  It will swell and expand if it gets wet.  So using spray or mist coolant or oils like Tap Magic is not recommended.

An alternative spoil board that we use is acrylic.  Acrylic is hard, flat, easier to machine than aluminum so it will not strain your machine and if you want/need to use lubricant, then you can without worrying about it damaging the spoil board.

No. While there are some “general purpose” end mills that will cut aluminum, some end mills are designed specifically for plastic, foam, wood or other non-metal materials.